Volkswagen
Owner:
Justin Gallien
Sarnia
Ontario / CANADA
Comments: Id Just like to thank Steve, Mike S, Mike Z, Lavi, Alex, Jacob and everyone else involved with what is the " Uni Crew". thanks for all the support guys! :-)
Engine:
Vr6 12v Head ReBuilt with :
-Supertech Engineering Stainless steel back-cut and dished valves (intake and exhaust)
-Supertech Engineering HD valve springs and Titanium lightweight retainers
-Autotech 262 cams
-Meyle lightweight lifters
-Stock 2.8L bottom end
With:
-Custom MSD Coilpack Conversion
-Autotech 10.3mm wire with MSD ends
- (Running NGK BKR7E 0.025" gap)
-Custom 4" air Intake w/big K&N filter
-Neuspeed Lightweight Pulley kit
-Garrett 60-1 T04s turbocharger (Cold Side 0.70 A/R)(Hot Side 0.63A/R)
-FMIC with (2.5" Aluminium piping to intercooler/3" Aluminium piping from intercooler to TB)
-ATP Clone Turbo Manifold
-Walbro 255 inline Fuel Pump
-Dual Eurojet Kugel Diverter Valves
-Bosch Greentop 440cc Injectors
-Schimmel Performance 8.5:1 Stainless Headspacer kit with gasket
-ARP Headbolt Kit
-Unitronic 440cc Software (of course)!
-2001 Audi A8 MAF housing + stock VR6 Sensor
-Custom Short Runner Intake done by Juan8595
-38mm Tial Wastegate with a 14.5psi spring
-Kinetic Manual boost controller
-Braided Oil Feed and Oil Return Lines
-Braided Fuel lines
-BFI dogbone mount stage 2
-VF Engineering engine mounts
-Act Stage 4 6-puck sprung Clutch kit with 9lbs Flywheel and HD pressure plate(rated:450hp/480ft/lbs)
-MK3 fuel Rail
-Eurospec 3 to 5 bar adjustable fuel pressure regulator
-A/C Delete
-SAI Delete
-Rear 02 Delete
-Manifold changeover valve delete
-Battery In Trunk
-Turbo Timer
-4” aluminium intake with 4” x6” K&N cone filter
Transmission:
-Stock O2J Trans with Peloquin O2J-A LSD
-Custom re-inforced clutch fork
-B&M Short Shift kit
Exhaust:
-3" Custom Downpipe
-42DD 3” cat-back system dual 3” tip magnaflow muffler
-Magnaflow highflow cat 3”
Suspension:
Rokkor Coilover setup
Brakes:
stock size Vr6 Brembo slotted and cross-drilled rotors and EBE pads
Exterior:
-Lowerered, Shaved door moldings/bumper moldings. -Molded rear valance.
-Custom front bumper with GLI front valence.
-mk3 jetta side skirts cut down and re-fiberglassed to fit the mk4.
-19"x8.5" VMR Audi RS4 B7 Replica's
-General Exlcaims UHP rubber all around 215/35/19
-Flat Black paint
Interior:
-Rear Roll bar and harness bar
-Recaro fighter replica seats
-5-point Harness's
-Rear seat delete
-R series Mats and Dead Pedal.
-Boost/Vacuum/Oil Pressure/ Oil Temp/Water Temp/Volts
-Innovate G3 A/F Gauge kit and Lambda O2 Sensor
GET CONNECTED!
STAY CONNECTED!
Wide R32 wot box 2-step backfiring @ H2O
Gallery
Unitronic @ Waterfest 16
Wed, 1 December 2010 3:56 pm
Unitronic @ Waterfest 16
2009 Unitronic Photoshoot
Mon, 7 September 2009 1:26 am
2009 Unitronic Photoshoot
Unitronic @ Waterfest 15
Wed, 26 August 2009 10:03 am
test
Testimonials
Norman Aguiar : WoW what can i say I have stage 2 tuning on my 2003 VW Jetta wolfsburg edition 1.8T. I was driving without the tuning for 3 years. I did some upgrades and mods to my car, for instance cross drilled rotors all the way around, intake system, 3" full exhaust turbo back, and an electric boost...
”
- UNITRONIC
- Home Page
- Become a Member
- Forgot your password?
- Privacy Policy and Transparency
- Terms of Use
- Company
- About us
- Company History
- Our Facility
- Our Team
- Events
- Testimonials
- Unitronic Chipped Genuine Products
- Privacy Policy and Transparency
- Job Opportunities
VISIT OUR MOBILE FRIENDLY WEBSITE
Unitronic Chipped: 4633 Louis B-Mayer, Laval, Quebec, Canada, H7P 6G5
Tel.: 1.866.341.2447 / Fax: 1.866.714.9893 / info@unitronic.ca
English / Français / Site Map / tracker
All Manufacturers name used in this web site are for identification purposes only.
All trademarks and registered trademarks such as Volkswagen / Audi / Porsche / Skoda / Seat / Opel / Volvo, DSG ( Direct-Shift Gearbox )... are the property of their respective owners.
